Plug ‘n Power was Radio Shack’s brand name for products that used the X10 power line communications protocol. X101 was developed in 1975 by Pico Electronics, Ltd. of Glenrothes, Scotland. Radio Shack, along with Sears, Roebuck & Co. (with the Sears Home Control System) and BSR (with the BSR System X-10), was among the first sellers of X10 compatible products.
Radio Shack Plug'n Power
Page 1 61-2576.fm Page 1 Wednesday, September 8, 1999 1:50 PM Cat. 61-2576 OWNER’S MANUAL Please read before using this equipment. Wireless Remote Control System. Page 2 Plug ’N Power system. You can turn on or off all lights or appliances plugged into your Plug ’N Power Wireless Remote Control System with the touch of one button from anywhere inside or outside your home. View and Download Radio Shack 49-1000 user manual online. Plug ‘n Power Wireless Security System. 49-1000 Security System pdf manual download.
Radio Shack introduced their first Plug ‘n Power products in late 19792. Most of the products were appliance and light modules. These plugged into an electrical outlet, and an appliance or light was then plugged into the module. Some of those modules included:
- Appliance Module (catalog number 61-2681) cost $16.99 (originally $15.99)
- Lamp Dimmer Module (catalog number 61-2682) cost $16.99 (originally $15.99)
- Universal Appliance Module3 (catalog number 61-2684) cost $17.99
- Wall Switch Module (catalog number 61-2683) cost $17.99
- Wall Outlet Module (catalog number 61-2685) cost $21.95
Plug ‘n Power devices from a 1981 Radio Shack catalog
The modules were designed to respond to commands sent over the electrical wires inside the house. They could turn on or off, or in the case of a lamp, change brightness. The advantage of using a power-line communication system was that it didn’t require any additional (and costly) signal wiring.
To control the devices, Radio Shack sold the Plug ‘n Power Remote Control Center (catalog number 61-2680) for $42.95. It was fairly small, measuring 4 3/4″ by 3½″ by 3½″. Like the other Plug ‘n Power modules, it just needed to be plugged into an electrical outlet to work.
As an example, you could plug a television into an Appliance Module and a lamp into a Lamp Dimmer Module. You could then plug in a Remote Control Center anywhere in the house and use the buttons to turn the television on or off and adjust the lamp brightness.
The TRS‑80 Plug ‘n Power Controller
TRS‑80 Plug ‘n Power Controller from a 1981 Radio Shack catalog
In 1981, Radio Shack introduced the TRS‑80 Plug ‘n Power Controller (catalog number 26-1182). It measured 4 1/2″ by 4 1/4″ by 1 1/2″ and cost $39.95. The Plug ‘n Power Controller worked with the TRS‑80 Model I, Model III, and the Color Computer.
Like the Remote Control Center, the Plug ‘n Power Controller used the electrical wiring to send control signals to Plug ‘n Power modules. Unlike the Remote Control Center, the Plug ‘n Power Controller connected directly to a TRS‑80 computer using the cassette port. This meant that up to 256 Plug ‘n Power devices could be controlled directly from a TRS‑80 using software.
From a 1981 Radio Shack Computer catalog:
Control up to 256 lights and appliances with your TRS‑80 Model I, III, or Color Computer. Activate security lights, start dinner, turn on the radio and much more — all from one central location! Nothing to install — just plug appliances into modules, and then into AC outlet and you’re all set.
One nice feature of the Plug ‘n Power Controller was a port to plug in a cassette recorder, coupled with a switch on the top of the unit with two settings: “CTRL” and “CASS”. Changing the switch to “CASS” allowed the TRS‑80 to read from the cassette recorder normally. Changing the switch to “CTRL” allowed the TRS‑80 to control the Plug ‘n Power devices.
Software for the Plug ‘n Power Controller came on two cassettes, with versions for the Model I, Model III, and Color Computer. There were also program listings in the 36-page manual.
The disadvantage of the Plug ‘n Power Controller was that the TRS‑80 had to be turned on and running the appropriate software to control the Plug ‘n Power devices. This meant that a complete home automation system needed to have a TRS‑80 permanently devoted to it.
In 1983, Radio Shack reduced the price of the Plug ‘n Power Controller to $19.95. It remained at that price until it sold out.
The TRS‑80 Color Computer Appliance/Light Controller
TRS‑80 Color Computer Appliance/Light Controller from a 1986 Radio Shack catalog
Radio Shack Plug N Power User Manual Download
The TRS‑80 Color Computer Appliance/Light Controller (catalog number 26-3142) was Radio Shack’s second TRS‑80-based X10 controller. It was introduced in 1985 for a price of $99.95. Unlike the earlier Plug ‘n Power Controller, the Appliance/Light Controller didn’t work with the Model I or Model III.
Instead of a cassette connection, the Appliance/Light Controller attached to the Color Computer using the serial port.4 Unlike the Plug ‘n Power Controller, the Appliance/Light Controller didn’t use the TRS‑80 to directly control appliances. The included ROM Pak software could program events into the Appliance/Light Controller, but that was the end of the computer involvement. The Appliance/Light Controller would turn appliances and lights on and off according to a schedule and without dedicating a computer to the task.
One quirk of the Appliance/Light Controller software was that it used an undocumented Color Computer video mode. This mode wasn’t one that Radio Shack supported when they created the Color Computer 3 later. The Appliance/Light Controller software was one of the few Color Computer 1/2 programs that wouldn’t run on the Color Computer 3.
Although Radio Shack didn’t sell any more TRS‑80-based Plug ‘n Power hardware, they did continue to sell and introduce new Plug ‘n Power devices. In fact, there were three pages of Plug ‘n Power items in the final Radio Shack catalog in 2002. Radio Shack no longer sells Plug ‘n Power devices5, but X10 compatible devices such as Appliance Modules, Lamp Control Modules, and Wall Switch Modules are still sold today.
- X10 was the tenth project developed at Pico Electronics. ↩
- Many sources identify Plug ‘n Power as having been introduced in 1978, but Radio Shack gave a date of first use as September 1979. ↩
- The difference between the Appliance Module and the Universal Appliance Module was that the Appliance Module could control appliances with two-prong electrical plugs but the Universal Appliance Module could handle appliances with two- or three-prong plugs. ↩
- The Appliance/Light Controller was a revised version of a Mattel Aquarius X10 interface that Pico Electronics never released. They revised it again into the CP290, which became the standard X10 controller for non-TRS‑80 computers. ↩
- Radio Shack’s Plug ‘n Power trademark was cancelled in 2010. ↩
Related Posts:
Categories: Hardware
Advertising
3
PLUG ‘N POWER PRECAUTIONS
Turning lights and appliance on and off by remote control
is a great convenience, but there can be some unexpect-
ed consequences. For example, you might unknowingly
turn on an empty coffee pot in another room, and it could
be damaged by overheating or could even start a fire.
You might also turn on an electric heater in another room
when flammable materials are close to the heater. Again,
damage or a fire could result.
is a great convenience, but there can be some unexpect-
ed consequences. For example, you might unknowingly
turn on an empty coffee pot in another room, and it could
be damaged by overheating or could even start a fire.
You might also turn on an electric heater in another room
when flammable materials are close to the heater. Again,
damage or a fire could result.
To prevent such problems, carefully plan what you want
to control (as described in this manual) and keep a chart
of your system handy. You must always be aware of what
you are controlling.
to control (as described in this manual) and keep a chart
of your system handy. You must always be aware of what
you are controlling.
SAFETY PRECAUTIONS
• Before using the product, please follow and adhere
to all warnings, safety and operating instructions
located on the product and in the owner's manual.
Save all instructions for future use.
located on the product and in the owner's manual.
Save all instructions for future use.
• Do not attempt to control lights or appliances that
exceed the ratings of the modules. If you want to
control lights or appliances that exceed the ratings of
the standard modules, see your local RadioShack
store for information.
control lights or appliances that exceed the ratings of
the standard modules, see your local RadioShack
store for information.
61-2576.fm Page 3 Wednesday, September 8, 1999 1:50 PM
Advertising
Popular Brands
Popular manuals